Hallo Gemeinde,
nach dem Update meines Tablets auf das Anniverary funktionieret Autorotate nicht mehr. Nachdem ich von der Seite des Sensorherstellers ein Treiberupdate installiert habe rotiert es zwar wieder, nur leider falsch. Im Troubelshooting zum Teiber ist folgendes zu lesen:
Troubleshooting:
================
If the screen does not rotate properly, you may need to adjust the chip mount configuration. This can be done with the factory_cal tool or by editing the registry.
OPTION 1:
To use factory_cal, lay the device flat with the screen facing up and run “factory_cal –mount 2” for MAP2, replace with needed map.
=> OK nur dieses Tool ist nirgends zu finden
OPTION 2:
The “ChipMount” value in the registry is found in device key HLKM\SYSTEM\CurrentControlSet\Enum\ROOT\SENSOR\0000\kxfusion
If device does not have chip mount info (an ACPI _CDM method), please calibrate with factory_cal or set a ChipMount value in the registry.
If the screen is rotated by 90 degrees and it changes the right way when the device is turned (screen goes counterclockwise when device goes clockwise), use DEVICE_MAP2 if the screen is counterclockwise, or DEVICE_MAP4 is it’s clockwise.
If the screen changes the wrong way (rotates the same way as the device), use DEVICE_MAP6 for counter, DEVICE_MAP8 for clockwise.
=> Nun kenne ich mich mit Regestry Einträgen zumindest soweit aus um dort auch Änderungen vornehmen zu können ohne das System zu schrotten Aber was ich genau wo eintragen soll kann ich hier nicht rauslesen, vielleicht kapier ich es auch nur nicht.
Leider habe ich vom Hersteller des Sensors noch keine Antwort erhalten, aber ich hege die Hoffnung das in der weiten Dr.Windowswelt vielleicht ein Wissender Unterwegs ist
Danke
LG
Armin
nach dem Update meines Tablets auf das Anniverary funktionieret Autorotate nicht mehr. Nachdem ich von der Seite des Sensorherstellers ein Treiberupdate installiert habe rotiert es zwar wieder, nur leider falsch. Im Troubelshooting zum Teiber ist folgendes zu lesen:
Troubleshooting:
================
If the screen does not rotate properly, you may need to adjust the chip mount configuration. This can be done with the factory_cal tool or by editing the registry.
OPTION 1:
To use factory_cal, lay the device flat with the screen facing up and run “factory_cal –mount 2” for MAP2, replace with needed map.
=> OK nur dieses Tool ist nirgends zu finden
OPTION 2:
The “ChipMount” value in the registry is found in device key HLKM\SYSTEM\CurrentControlSet\Enum\ROOT\SENSOR\0000\kxfusion
If device does not have chip mount info (an ACPI _CDM method), please calibrate with factory_cal or set a ChipMount value in the registry.
If the screen is rotated by 90 degrees and it changes the right way when the device is turned (screen goes counterclockwise when device goes clockwise), use DEVICE_MAP2 if the screen is counterclockwise, or DEVICE_MAP4 is it’s clockwise.
If the screen changes the wrong way (rotates the same way as the device), use DEVICE_MAP6 for counter, DEVICE_MAP8 for clockwise.
=> Nun kenne ich mich mit Regestry Einträgen zumindest soweit aus um dort auch Änderungen vornehmen zu können ohne das System zu schrotten Aber was ich genau wo eintragen soll kann ich hier nicht rauslesen, vielleicht kapier ich es auch nur nicht.
Leider habe ich vom Hersteller des Sensors noch keine Antwort erhalten, aber ich hege die Hoffnung das in der weiten Dr.Windowswelt vielleicht ein Wissender Unterwegs ist
Danke
LG
Armin